Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Alternative Cars, Part 3 - Turbine

A whistling engine...

by Julian Edgar

Click on pics to view larger images


Last week in Alternative Cars Part 2 we looked at the possibility of cars powered by solar energy. This week, we look at the potential for gas turbine cars.

Aircraft have shown the way with the transition from piston to turbine engines. During WWII, piston aircraft engines became very sophisticated, with examples featuring double overhead cams, four valves per cylinder, variable valve timing and turbo- and supercharging. But within 10 years, piston engines disappeared from nearly all high performance aircraft, replaced by turbines. Gas turbines are used in helicopters, trains, tanks and small power stations as well.

Click for larger image

Some car manufacturers – especially Chrysler and Rover - have in the past invested heavily in turbine development, in the case of Chrysler reaching the stage of having road-going prototypes in public hands. A turbine-powered race car (pictured) even contested the 1968 Indy 500 – and went very close to winning it.

So why haven’t turbine-powered cars taken off?

Function

Turbine engines can be divided into two classes – centrifugal and axial. However, in both cases the fundamental operating principles are the same.

A turbine uses a compressor and a turbine, with both mounted on the one shaft. Air enters the engine and is compressed by the rotating compressor blades. Fuel is then added to the compressed air flow and combusts, causing the gas to expand through the turbine that in turn extracts power from the hot gases. Since the turbine and compressor are on the one shaft, the turbine drives the compressor to further compress the entrance air.

Click for larger image

A centrifugal turbine engine (pictured) is rather like a car turbo in design – the compressor throws air out a side exit and the turbine is driven through gases reaching its blades from the side. In a centrifugal turbo, the combustion chambers are in the ‘pipes’ that join the compressor exit and the turbine inlet. In an axial flow design the air passes through multiple fan-like blades, staying parallel to the long axis of the engine and altering pressure at each step. The combustion chamber is usually internal to the engine. Some gas turbines have both axial and centrifugal elements in the design.

In a jet aircraft engine, the flow of gas from the engine produces thrust that in turn pushes the aircraft along. However, in automotive (and helicopter, train, tank and power station) applications, the flow of gas from the compressor turbine is used to spin another turbine which is geared to a shaft that provides the power output. The advantage of using a separate turbine to extract power is that the main part of the engine can be revved to full power while the output turbine is stationary. This allows the development of maximum torque when at rest, with the torque output decreasing as the vehicle travels faster.

In automotive applications, where small turbines are used, efficiency is lower than that achieved for large turbines. To improve efficiency, the hot exhaust gases are used to preheat the intake air, so reducing the amount of fuel needed to obtain the same internal combustion gas temperature. This heat exchanger is sometimes known as a recuperator or regenerator.

These rare diagrams show some of the prototype automotive gas turbine engines developed in the 1950s.

Click for larger image

The 1954 120hp turbine engine by Chrysler.

Click for larger image

The Boeing 502 gas turbine had an output of 160hp and used a single stage axial compressor and turbine. It was installed in a Kenworth truck.

Click for larger image

Fiat designed and built this 200hp turbine car in 1954. The engine used a two stage centrifugal compressor and a two stage axial turbine.

Advantages

The advantages of a turbine engine for car use include a lack of vibration, high power/weight ratio and compact size (although both aspects depend on whether a recuperator is used) and the ability to burn a variety of fuels, including those of low octane. A multi-ratio gearbox is not needed - although step-down gearing is.

Finally, there is a wealth of knowledge available on the design and construction of turbines.

Disadvantages

However, as is clear by their lack of widespread use, the disadvantages are large.

The primary negatives are high cost (expensive high temperature materials needed) and high fuel consumption. The latter is mostly the case because at part throttle, turbine engines are very thirsty for the amount of power being produced. Gas flows (both intake and exhaust) are also very large, so effective filtration is bulky and exhaust silencing needs to be comprehensive. Emissions performance to car legislated standards is also problematic.

Solution

It’s unlikely that gas turbine cars will be commercially produced. However, one possibility is to use a very small turbine that works continuously at maximum power, driving a generator that charges a battery and/or makes power available to an electric motor. However, even in this scenario, battery losses would reduce overall efficiency quite considerably. (In fact in 1993 General Motors developed a gas turbine hybrid version of its EV1 electric car.)

The major advantage of gas turbines for aircraft (their ability to work at high altitude being the primary one), and in helicopter and small power station applications (fuel-efficient when working continuously at full power) do not apply to cars.

Conclusion

Click for larger image

It’s likely that the gas turbine cars produced by Chrysler and the prototypes developed by Rover (and Boeing, Turbomeca, Laffly, SOCEMA, Fiat, GM, Renault and Austin) in the 1950s and 1960s will be the only gas turbine cars to see the light of day.

See also The Chrysler Turbine Car

Next week: human powered vehicles

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
This is what happens when you put a current Merc diesel into a 20 year old body!

Special Features - 12 January, 2010

Mercedes Makeover

Measuring how air flows in and under a car

DIY Tech Features - 28 May, 2004

Undertrays, Spoilers & Bonnet Vents, Part 1

Aluminium bellmouths in minutes

DIY Tech Features - 10 December, 2013

Making your own Bellmouths

How Chrysler developed a 2.4 litre turbo

Technical Features - 5 July, 2003

Designing a Factory Turbo Engine

The best shape for inlet pipes

DIY Tech Features - 29 January, 2002

Ballistic Bellmouths

The electric motor and control system for a DIY electric bike

DIY Tech Features - 11 February, 2005

Building an Electric Bike Part 2

All the detail on how direct petrol injection systems work

Technical Features - 3 January, 2007

Direct Petrol Injection

Not just the largest aircraft made of wood, but also with incredible underskin technology

Special Features - 29 September, 2009

The Spruce Goose

An astonishing car

Special Features - 20 May, 2014

The Rumpler Tropfenwagen

Building and installing the in-wall speakers

DIY Tech Features - 11 December, 2012

Sound in the Lounge, Part 3

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip