Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Smart Mixture Meter, Part 1

Mixture indication plus an alarm that protects your engine from high load lean-out!

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Update to our hugely successful LED Mixture Meter
  • Rich/lean status on 10 LEDs
  • Available in kit form or pre-built
  • Lean-out alarm
  • Auto night dimming
Email a friend     Print article

It’s one of the most popular articles ever published in AutoSpeed: the Mixture Meter covered in Cheaply Monitoring Air/Fuel Ratios has now been built in the thousands. As a simple and easily fitted indicator of the rich/lean status of the engine, it’s waaaaay better than having no instrument at all. (And of course, it’s not nearly as good as having an expensive professional wide-band air/fuel meter on the dash, either!)

But while it’s been a very successful design, we thought that it could be improved upon. Specifically the new Smart Mixture Meter covered here:

  • Has better protection of the main IC, resulting in a much lower chance of damage when power surges occur
  • Allows the LEDs to be auto-dimmed at night
  • Has an audible alarm that sounds when there are lean mixtures present at high loads

If you’ve ever done any electronics soldering and you can recognise some components, the AUD$25 kit is easy to build. (And if you don’t want to build it, the module is available fully built and tested for AUD$70.)

This week we’ll cover the design and next week we’ll install it step-by-step in a car.

The Background Story

The Smart Mixture Meter was developed and designed by www.siliconchip.com.au electronics magazine. It is one of a number of projects that will be covered in a unique Silicon Chip publication - High Performance Electronic Projects for Cars - which will be available from newsagents in Australia and New Zealand, or online through the AutoSpeed shop. Additionally, it has also been published online at A Smart Mixture Display For Your Car.

The electronics design of the Smart Mixture Meter was carried out by electronics engineer John Clarke, while I came up with the concept. (During this period I wore a different hat to an AutoSpeed contributor, working for Silicon Chip Publications as a freelance contributor.) AutoSpeed’s Michael Knowling did the on-car testing.

So by no means should the Smart Mixture Meter be seen as an AutoSpeed-developed project, at the same time I am happy that AutoSpeed endorses it and promotes it.

Julian Edgar

The Smart Mixture Meter

Click for larger image

As with the previous design, the Smart Mixture Meter uses 10 LEDs arranged in a moving dot bargraph display. There are two yellow LEDs (indicative of rich mixtures), six green LEDs (mixtures of ‘middle’ strength) and two red LEDs (these show lean mixtures – remember, red is for danger). The Smart Mixture Meter is designed to work with zirconia oxygen sensors, that output a range that varies from about 0 – 1 volt. When the mixtures are rich, the sensor outputs a higher voltage (eg above 0.8 volts); when the mixtures are lean, the sensor outputs a low voltage (eg below 0.2 volts).

If you think of each LED lighting up in turn as the output voltage of the oxy sensor changes from 0 to 1 volt, you’ll be pretty close to understanding how the display works.

Oxygen sensors are used by the engine management system for feedback – the Electronic Control Unit (ECU) uses the signal to keep mixtures around what’s called ‘stoichiometric’, or an air/fuel ratio of about 14.7:1. From the designers’ point of view this is a desirable air/fuel ratio because the cat converter works best at this ratio, so emissions are able to be kept low.

The zirconia oxy sensor is particularly suited to this application because its output voltage rapidly changes as the air/fuel ratio goes through 14.7:1. At air/fuel ratios leaner than this the voltage is low, then it switches very quickly to a higher voltage as the air/fuel ratio becomes richer than stoichiometric. IOTW, the output voltage of the oxygen sensor is very non-linear compared to air/fuel ratio. (See The Technology of Oxygen Sensors for more tech on sensors.)

But you want an English translation of all that? - the raw voltage output of the oxy sensor isn’t really great for monitoring mixtures.

However, people who don’t go any further with this idea often therefore assume that a mixture meter of this sort is useless. After all, if it can’t tell you whether your car is running 11:1 or 12:1 air/fuel ratio, what use is it? In fact, in a car the Smart Mixture Meter is extremely functional. This is because:

1.       Rapid Diagnostics

If the engine suddenly starts to run badly, by looking at the Smart Mixture Meter you can immediately tell if it’s an air/fuel ratio problem. In fact, have a Smart Mixture Meter in the car and if the engine stumbles, the first instrument you look at is the LED display. Is the engine suddenly running ultra-lean? If so, perhaps the fuel pump or fuel pressure regulator has died. Or is the engine running badly because the mixtures are over-rich? That might be indicative of an airflow meter or MAP sensor problem. Without having the immediate and graphic indication on the dash, it’s just so much harder to find what the problem is.

2.       Oxygen Sensor Condition

You can clearly see the health of the oxygen sensor. The ECU doesn’t use the signal from the oxy sensor all the time to control mixtures to 14.7:1. In most cars, at full throttle and on the over-run the ECU instead adopts what’s called an ‘open loop’ strategy – it ignores the output of the oxy sensor and goes just on its internally programmed maps. (When the oxy sensor signal is being used by the ECU the car is said to be in ‘closed loop’.)

All this is really easy to see on the Smart Mixture Meter. By using the output of the factory sensor the high-speed fluctuations in mixture strength are easily able to be seen. So when the ECU is in closed loop, you’ll see the middle LEDs flashing back and forth as the ECU rapidly corrects the mixture strength to keep the average air/fuel ratio at 14.7:1. When the ECU uses open-loop control, only a single LED will be illuminated as the mixture strength is kept constant.

A sick oxygen sensor will show up as the closed loop cycling back and forth of the LED will be slow. And a dead oxy sensor? Well, you won’t have any LED lit, will you!

3.       Audible Alarm

In addition to its LED display, the Smart Mixture Meter has another important function. It monitors engine load by taking a feed from the airflow meter. When the load is high and the air/fuel ratio is lean, the alarm sounds. Since these two conditions should never occur together, you should never hear the alarm (apart from when setting the system up).

This feature is a real plus because it will immediately warn you of a catastrophic lean-out. These can occur when you get fuel surge when cornering hard (I lost an engine once that way) or when accelerating at full power and a fuel reg hose falls off. In both cases, you won’t normally be watching the LED display....

So you can see that despite the fact that the Smart Mixture Meter doesn’t give you an exact numerical read-out of air/fuel ratio, it’s actually a bloody useful display to have running in a car. (And don’t think that it’s impossible to tune by the output of a standard-type oxy sensor – see Real World Air/Fuel Ratio Tuning.)

The Signals You Need

For the Smart Mixture Meter to work you’ll need a car equipped with a zirconia-type oxygen sensor that outputs a signal in the 0-1 volt range. To use the lean-out alarm feature you’ll also need to access a voltage within the 0-5V range that rises with engine load. Most typically, that’ll be an airflow meter output, but in a turbo car you can probably also use a MAP sensor output.

Rather than being disappointed after building the kit (or after buying the preassembled version), first use a multimeter to measure the outputs of these sensors to make sure that you’ll have the right signals available.

1.The Oxygen Sensor

Click for larger image

The oxy sensor will be mounted in the exhaust manifold or first section of the exhaust pipe. In some turbo cars it is mounted in front of the turbo but in most cases, it is immediately after. Many cars these days use multiple oxygen sensors – eg four sensors aren’t uncommon on a V6 or V8. However, you’ll need to tap into the output of only one, which should be close to the engine.

Older cars use oxy sensors with just one output wire. That’s pretty easy – just use a multimeter to measure its output voltage when the engine is fully warmed up. It should be around 0.5 volts (ie 500 millivolts) at idle (probably with lots of up/down movement) and rise to 0.8 – 0.9 volts (800 – 900mV) under load.

(To do this, set the multimeter to Volts DC and connect the black lead to the car’s body. Start the car and let it warm up. With the other multimeter input, back-probe the working oxygen sensor.)

If you’re dealing with a multi-wire oxy sensor, just probe each wire in turn until you find a voltage that behaves in the way described above.  Other wires are likely to have 0 volts (ie ground) and battery voltage on them.

The connection to the signal sensor output wire can be made either under the bonnet or at the ECU, which is usually mounted inside the cabin. The ECU connection is better (there’s less chance of picking up funny signals) but either way usually works fine.

2.The Airflow Meter

Finding this signal is done in much the same way, but this time you’ll be backprobing the plug at the airflow meter. What you’re looking for is a signal that varies within the range of 0-5 volts. At idle expect to find about 1-1.5 volts, while sharp blipping of the throttle should take this up to 3 volts or so. Under full load on the road the voltage should rise to about 4.5 – 5 volts. There may be other voltage signals that vary a bit when the throttle is blipped, so don’t just do a cursory test.

The Adjustments

Click for larger image

The Smart Mixture Meter has no less than five adjustable pots – which seems a helluva lot! However, when they’re broken down into their different functions it becomes easy.

  • Dimming
  • VR3 (the pot on the far right) simply adjusts how much the LEDs auto dim at night. Clockwise will give you a brighter display at night.

  • Adjusting the Display
  • Because not all oxy sensors work over the complete 0-1 volt range, adjustments are needed so that on a properly running car the lit LED isn’t always up one end or the other. Pot VR1 allows you to adjust the range so that the end yellow LED lights when mixtures are fully rich. This should occur at full throttle, high rpm. Pot VR2 is the adjustment for the other end of the range – you should set this pot so that when the car is in closed loop, the up/down movement is centred around the middle LEDs.

  • Adjusting the Lean-Out Alarm
  • There are two adjustments for the lean-out alarm – the load and the LED. Pot VR5 sets the Load Threshold – adjust this until LED 12 (the bottom LED on the PCB) comes on only at reasonably heavy loads. Then adjust pot VR4 until LED 11 (the other red LED on the PCB) comes on at what would be a lean mixture for that high load.

    For example, in a turbo car set pot VR5 so that LED 12 lights when you’re just coming onto boost. Then set VR4 so that LED 11 lights when the last green bargraph LED before the red is on.

    Depending on the operating system of the car you may need to do some tweaking of these adjustments before there aren’t any false alarms in normal driving. (But set them so that there are just no false alarms, if you see what I mean!)

    Once you have installed a LED Mixture Meter on your dashboard, it is very hard to go back to having no mixture indication at all. Not only do you feel blind without it, you can also rest easy knowing that you’ll be instantly warned of a catastrophic lean-out.

    Next week: the step-by-step fitting of the Smart Mixture Meter to a car.

    Buy the Smart Mixture Meter: AutoSpeed Shop
    You can buy products mentioned in this article here :
    KC5374 : Smart Fuel Mixture Display for Fuel injected Cars
    ASKIT-5374 : PRE BUILT Smart Fuel Mixture Display for Fuel injected Cars

    Did you enjoy this article?

    Please consider supporting AutoSpeed with a small contribution. More Info...


    Share this Article: 

    More of our most popular articles.
    The mechanics of diesel engine fuel systems

    Technical Features - 20 January, 2007

    Common Rail Diesel Engine Management, Part 1

    DIY timer module adds delays or extended 'on' periods to any electric car function

    DIY Tech Features - 1 September, 2008

    The eLabtronics Timer

    A home-built jet-powered kid's scooter...

    Feature Cars - 23 January, 2007

    John's Jet Madness!

    How good were they?

    Special Features - 15 June, 2010

    The First Holdens

    Looking at the future of hydrogen-fuelled cars

    Special Features - 28 April, 2009

    Will Hydrogen Happen?

    Electronic module that can sound high or low temperature alarms or warnings

    DIY Tech Features - 30 June, 2008

    The eLabtronics Pulser, Part 2

    Country driving skills have almost disappeared - here are some

    Special Features - 4 October, 2011

    How Not to Die this Week

    Japan's first supercar

    Special Features - 8 February, 2008

    Toyota 2000GT

    The Eighties Group B rally cars with up to 600hp

    Special Features - 21 February, 2003

    The Early Days of Turbo Part 2

    How to use relays - some of the most useful electrical components ever!

    DIY Tech Features - 28 November, 2005

    Using Relays

    Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
    Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip