Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us

Metal Casting, Part 3

Watching an aluminium intake manifold being poured

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Last in a 3-part series
  • Seeing the aluminium poured...
  • ...and then the sand mould broken open
  • Cleaning-up the casting
Email a friend     Print article
This article was first published in 2008.

Click for larger image

Last week in Metal Casting, Part 2 we saw how a sand mould for an aftermarket inlet manifold was formed. Now it’s time to watch the pouring of the aluminium and then see the results. As with the previous parts in this series, the work was being done at the Matilda Foundry in Maryborough, Queensland. The casting is a Funnelweb 2V 351 Ford V8 inlet manifold by Parker Racing.

Click for larger image

The aluminium is melted down from ingots. The aluminium most often used by this foundry for sand casting is AA601 (US standard 351). This material can be heat treated and machines well.

Click for larger image

The ingots are melted in either a gas furnace (pictured) or an electric furnace. A layer of oxide floats on top; it insulates and keeps the air from the molten alloy.

Click for larger image

The temperature of the molten alloy is directly measured with a thermocouple. It needs to be at about 710 degrees C.

Click for larger image

What look like oversize soup ladles are used to transfer the molten alloy from the furnace to the mould. With a casting of this size, two pourers are used; they time their pour with a countdown so that both mould runners are filled simultaneously.

Click for larger image

Ceramic filters have previously been placed in the runners, preventing any impurities from passing into the casting. The filters also reduce the inclusions of air causing the formation of aluminium oxides.

Click for larger image

The mould is filled to the top of the risers and runners, the molten material actually forming an inverted meniscus at the surface. A special powder called Feedex is then placed over the exposed aluminium; this keeps it from the air and also...

Click for larger image it burns, keeps the riser material from freezing before the casting has solidified. (This allows the riser to feed material to the shrinking casting.)

Click for larger image

The casting is left to cool and then fork-lifted to an area where the sand mould can be broken off. The sand has become very hard and is removed with a hammer...

Click for larger image

..and pneumatic chisel. Note the sand falling out of the space between the intake manifold runners.

Click for larger image

The bare casting is given a quick onceover with a sandblaster, primarily to remove the casting sand that would otherwise damage the...

Click for larger image

...bandsaw that is used to cut off the risers and runners. This material is remelted in the furnace.

Click for larger image

A die grinder is then used to remove the casting flash – the thin edges of metal that show the parting line of the sand mould.

Click for larger image

The foundry’s work with the casting is then finished – the casting is ready to go to the machine shop to be faced and have holes drilled.

Die Casting

In this series we’ve covered sand casting – as its name suggests, castings made with sand moulds. But another type of casting - called die casting - is often used, especially of small parts required to be made in large numbers. Die casting uses a two-part steel die.

Gravity die casting uses a similar approach to sand casting in that the molten metal is simply poured into the die. Pressure die casting injects the metal under pressure.

Die casting can achieve a better surface finish (the molten metal is in contact with a smooth steel surface, rather than sand), can be dimensionally more accurate, and yields little flash. Because of its cooling contact with the metal die, small die castings can be removed only minutes after being poured. The dies are configured with rollers, levers and hinges, allowing the die to be opened, the solidified casting to be pushed out and then the die again closed, ready for another pour.

Matilda Foundry does some gravity die casting, usually in EA401 aluminium.

Click for larger image

Examples are this boat anchor (shown with its mould)...

Click for larger image

...and this fitting (formed in two parts) that is used to support the roof handrail in trains.


As has been seen from this series, developing the pattern for (say) a new intake manifold isn’t the sort of thing that you whip up overnight, get the sand mould made the next day and then have the finished casting back at your house a day later!

However, knowing exactly how castings are produced in small quantities opens up a range of possibilities that may never before have occurred.

Thanks to Matilda Foundry for their major help in preparing this series.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...

Share this Article: 

More of our most popular articles.
Clearing the space

DIY Tech Features - 10 January, 2012

A New Home Workshop, Part 1

A home-built jet-powered kid's scooter...

Feature Cars - 23 January, 2007

John's Jet Madness!

Books that you'll keep forever

Special Features - 24 March, 2009

The Ten Must-Have Books

Building and installing the in-wall speakers

DIY Tech Features - 11 December, 2012

Sound in the Lounge, Part 3

The electronics of diesel engine fuel systems

Technical Features - 29 January, 2007

Common Rail Diesel Engine Management, Part 2

A new engine designed to extend the range of plug-in hybrid cars

Special Features - 8 December, 2009

The Lotus Range Extender Engine

One of the best electronic car modification tricks you ever saw

DIY Tech Features - 15 October, 2013

Pots aren't just variable resistors

If you do any work with your hands, you need one of these.

DIY Tech Features - 28 July, 2008

Bench Vices

Is it worth producing your own fuel?

Special Features - 4 March, 2008

Making Your Own Bio-Diesel

Steps in mixing and matching front brake components

DIY Tech Features - 29 May, 2012

Selecting components for upsized front brakes

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip