Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us

Modifying Electronic Car Handling Systems, Part 3

More on switching off traction control while leaving the stability control working!

by Julian Edgar

Click on pics to view larger images

At a glance...

  • How to turn off traction control without changing stability control
  • Using relays to do the switching
  • ABS continues to operate normally
  • Part 3 of a 4-part series
Email a friend     Print article
This article was first published in 2004.

This is Part 3 in this series. In Modifying Electronic Car Handling Systems, Part 2 , we covered how it is possible to disable traction control while still leaving stability control working. So why would you want to do that? Well, it lets you have a lot more fun in a car – you’re able to spin the wheels and have much better throttle-steering through corners, while at the same time the safety net of stability control is still there if you get right out of shape.

And don’t think that modifying the systems like this is very complex – it isn’t. Basically, all that we do is tell the ECU that the driven wheels aren’t spinning any faster than the undriven wheels. That way, the ECU doesn’t know when the driven wheels are slipping! It’s easy to achieve this by disconnecting the speed inputs from the driven wheels and replacing these signals with the ones from the undriven wheels. In effect, the undriven wheels (eg the front wheels in a rear-wheel drive car) feeds both the front and rear speed inputs.

Click for larger image

This diagram shows how it’s done in a front-wheel drive car. Because wheel speed sensors are inductive, they have enough grunt to drive the extra inputs without any problems.

However, making this wiring change permanent as is shown here has two problems:

  • the ABS won’t work
  • it’s difficult to quickly swap back to standard when you want full traction control

But both of these problems are easily overcome!

If you have a car with just traction control, you might be puzzling of the need for a system like this. After all, there’s an ‘off’ switch on the dash and when you don’t want traction control, you just press it, right? However, all cars with stability control also have traction control – and a single dashboard switch that turns off both systems. The approach covers here allows you to retain stability control (and ABS) while dispensing with traction control.


A relay is just a remote-controlled switch. In this application, that sounds pretty good – you can remotely change whether you have the traction control working or not. And by using two DPDT relays and another SPST design, it’s even easy to have the sensor operation return to normal whenever you put your foot on the brakes – ie ABS operates as normal.

However, experience has taught us that when we mention relays – especially non-automotive relays – many readers get confused pretty fast. So, unless you’re right up to speed with relays, their functions and types, please read the following carefully!

Lots of automotive enthusiasts are as happy as Larry in wiring up relays to control heavy loads - lights, fans and so on. After all, there are just two wires that supply power to the coil to switch on the relay, and two other terminals that get connected together when the relay is on. But it's when relays have five and eight connections that some start to sweat. But if a few overall ideas are kept in mind, there's no need for hassle.

Firstly, just as with those simple car relays, all relays have two terminals for the coil. A relay is just an electromagnet-based switch, and the coil makes the electromagnet happen.

Click for larger image

A normal car relay is a single pole, single throw (SPST) design. This designation refers to the switching part of the relay where when it's activated, one wire (a "single pole") can be connected only one way (a "single throw"). Just like a simple on/off switch, when you power up the relay's coil, the connection is made; when you unpower the coil, the connection is broken. In this diagram the relay's coil is yellow. Near to the coil you can see a switch, which is open. This is called a Normally Open contact - it's open when there's no power being applied to the relay. When power is applied to the relay, the single contact closes. This is a Single Pole Single Throw relay - SPST.

Click for larger image

But wouldn't it be good if we had another contact that was broken as the relay closed? That's what happens in this design. Another contact has been added that is Normally Closed. When the relay is energised, this contact is broken and the other one (the Normally Open contact) is closed. We still have only a single pole to be switched, but now it can be connected two ways - a double throw design. This type of relay is therefore called a Single Pole, Double Throw relay. As you can see, it has both Normally Open (NO) and Normally Closed (NC) contacts. Some people call this a changeover relay.

Click for larger image

In the above design a single circuit could be switched in two different directions. But why not switch more circuits at the same time? That's what this design does - it's a Double Pole, Double Throw relay. The 'Double Pole' bit just means that it has two separate inputs that can be switched - and we now know what the 'double throw' stuff means.

With this type of relay when the relay is activated you can:

- turn on two completely independent circuits

- turn one off and one on

- turn off two completely independent circuits

Even more complex designs of relay exist, but if you analyse their specs on the basis of how many poles and throws they have, it becomes a helluva lot easier to understand!

Relays are really good items to get your head around because once you understand them, you can do many things with them. They’re also rugged (eg unlike transistors and integrated circuits, you can’t very easily blow up a relay), easy to drive, cheap, widely available and versatile.

Click for larger image

Ok, so take a look at what we need to do with the relays. This time we’ve halved the car – we’re looking at only one side. As you can see, when we want the traction control to stop working on a rear-wheel drive car, we need to change the input pair of wires normally connecting the ECU to the Rear Left wheel to the Front Left wheel.

Click for larger image

Or, to show it another way, here you can see that the ECU input needs to either connect to the rear wheel sped sensor or the front wheel speed sensor. Think about the relay labels used above and you’ll realise that what we’re talking about here is a double pole (the two wires that go into the ECU), double throw (they either go to the front wheel sensor or rear wheel sensor). Hmm – and a Double Pole Double Throw 12V relay costs about AUD$6!

Click for larger image

Here’s the relay in place. It initially looks confusing but let’s take it step by step. The two wires going to the Rear Left Wheel speed input on the ECU connect to the two Common (“C”) terminals of the relay. As is shown by the two arrows, these wires can then be switched two ways. At the moment they’re shown connected to the Normally Closed (“NC”) terminals, which are wired to the Rear Left speed sensor. In other words, when there is no power applied to the relay’s coil, the system works completely as normal – all the correct wheel speed sensors are connected to the correct inputs.

But when power is applied to the relay coil, the Commons are switched to the Normally Opens, which in this case connects the Rear Left speed input on the ECU to the Front Left sensor. At the same time, the Rear Left sensor is disconnected.

Click for larger image

OK, but how do we make the relay change? That’s as easy as applying 12V to the relay’s coil. As shown here, a switch, 12V supply and earth connection are all that’s needed. Close the switch and traction control disappears.

Click for larger image

The next step is to add the final relay so that when the brake lights come on, the system returns to normal wheelspeed sensing. This requires just a Single Pole Double Throw design. As you can see, the coil of the main DPDT changeover relay is fed through the Common and Normally Closed contacts of the SPDT relay. This means that, as shown, the Changeover Relay is normally in the ‘no traction control’ position, with the front speed sensors feeding both front and rear ECU inputs. However, when the brakelights come on and 12V is made available to the Switching Relay, power is turned off to the Changeover Relay so the contacts drop back to their Normally Closed positions, returning the traction control to standard.

Click for larger image

To provide a manual Traction Control on/off switch, all that’s needed is a switch positioned as shown here.

The circuit has been designed so that if power is lost to the system, the traction control returns to standard.

These diagrams show only half of the system. To complete the system, just mirror-image the wiring for the other side of the car. (Note you can use the one Switching Relay to operate both Changeover Relays.)

Yes there are lots of wires that need to be connected, but yes, it’s just a bunch of switches being made....

Next week we’ll show you step by step how to make it happen.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...

Share this Article: 

More of our most popular articles.
Fuel cells are being touted by mainstream car companies, but you have to wonder...

Technical Features - 24 October, 2007

Alternative Cars, Part 7 - Fuel Cells

Developing a new Human Powered Vehicle suspension system

DIY Tech Features - 13 July, 2010

Chalky, Part 8

Modifying the regen braking system on a Toyota Prius

DIY Tech Features - 15 December, 2004

A World First: Modifying Regen Braking

Making a new airbox intake - but did it improve performance?

DIY Tech Features - 8 February, 2011

Powering-Up the 1.9 litre TDI, Part 2

Finding why a V8 Cobra replica was getting hot under the collar

DIY Tech Features - 14 April, 2009

Chasing Overheating

Giving factory seats more support and comfort

DIY Tech Features - 17 March, 2009

Reshaping Factory Seats

Drains and landscaping - and passing council inspection!

DIY Tech Features - 9 September, 2008

Building a Home Workshop, Part 5

A brilliant new temperature controller that's so cheap it's unbelievable.

DIY Tech Features - 15 November, 2011

$25 Temperature Controller and Display!

Designing for body stiffness

Technical Features - 14 December, 2010

One Very Stiff Body!

Building an adjustable temperature alarm - and more!

DIY Tech Features - 27 October, 2009

eLabtronics EZ System, Part 4

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip