Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Fitting Front Camber Adjusters

The step-by-step of fitting a front camber kit

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Camber kit for MacPherson struts
  • Step-by-step of install
  • Installation problems we found
  • Handling and steering results
Email a friend     Print article
This article was first published in 2004.

If you have a car with front MacPherson struts, it’s easy to add camber adjustors. These allow you to dial-in some negative camber which aids in steering feel and reduces understeer. (So what’s negative camber, then? It’s the angle that the front wheels lean inwards at the top when the car’s viewed end-on.)

Camber adjusters which are fitted at the bottom of the strut rely on the fact that just two bolts are used to connect the strut to the casting that supports the stub axle. If you move the top bolt towards the centreline of the car, or the bottom bolt outwards, negative camber will result. So let’s take a look at fitting a camber kit – in fact, we chose to fit two full kits. So why two? Well, read on!

The Kits

Click for larger image

We used two K-Mac camber kits. These kits use full-size replacement bolts rather than the smaller diameter, crank-offset bolts used in some kit designs. (Well, that’s not entirely true, as we’ll come to later.) Each kit costs AUD$130 direct from K-Mac.

Click for larger image

This diagram - from the car’s workshop manual - shows how two bolts locate the wheel assembly with regard to the strut. It’s these bolts (circled) which are replaced by the camber kit. Normally, just the top bolts on each side are replaced but to get maximum adjustment, we used two kits and replaced both top and bottom bolts on each side.

Click for larger image

Here’s what one of the new bolt assemblies looks like. From left is the new bolt – note the flat machined along the entire length. Next is an eccentric washer – it’s important to firstly note the hole is ‘keyed’ to match the cross-section of the bolt, and secondly that the hole is not located in the middle of the washer - ie it’s eccentric. Next is a guide-plate with a slot built into it, followed by a bush, a slotted washer, a non-eccentric washer, two more washers (sitting on top of each other) and a nut. Confused? It gets clearer in the next pic.

Click for larger image

You can see from this ‘assembled’ view that the eccentric washer sits within the slot in the guide-plate. If the bolt is turned, the eccentric washer bears against the plate, causing the bolt to move laterally within its slot. Now that’s just what we want to change the camber – a laterally moving bolt in the lower suspension assembly. So if the guide plate is fixed to the lower strut assembly, and if the bolt passes through the wheel support casting, then turning the bolt will wind in or out camber. And if we replace both upper and lower bolts, we’ll be able to get double the amount of adjustment.

Click for larger image

Here’s a complete K-Mac camber kit. There are the two bolt assemblies and also a drill-bit designed to enlarge the holes in the suspension strut so that the slotted washers (one integrated into the guide-plate and the other at the other ends of the bolts) can be fastened to the strut.

Drilling

Click for larger image

The holes can be drilled with the strut assembly still on the car – you just undo one bolt sufficient to pivot the other holes out far enough to do the drilling. However, for reasons that will soon become obvious, we chose to do the work off the car. That meant the top strut retaining nuts needed to be undone, the bottom pair of bolts undone and the sway bar disconnected.

Click for larger image

With some undoing of brake line and ABS cable retaining brackets, the strut could then be removed from the car. Note the arrow drawn on the strut top (above) so that the correct orientation was again easily found when it came time for re-installation.

Click for larger image

The provided K-Mac drill-bit fits into a normal portable drill. The holes in the channel section of the lower strut are drilled out – here the top hole has already been done and now the bottom hole is being enlarged. Note that when one camber kit only is being installed, just the top holes are drilled out. The drill-bit was lubricated with penetrating spray, explaining the smoke.

Click for larger image

The drill-bit, formed from a piece of tool steel forced at right-angles through a shaft, tends to break through unevenly and so leaves some edges that need to be cleaned-up with a round file.

Welding

Click for larger image

The guide plate can then be inserted into one of the enlarged holes. It has legs that extend over the other bolt, helping to keep the slot that’s integrated in the guide plate parallel with the road – that’s the direction the bolt needs to be able to move back and forth in when adjustment is being made. However, in our case, where camber kits were being installed in both holes, these legs were much too long so they were cut off short.

Click for larger image

Here one of the kits has been temporarily inserted and the other is being put into place (note the shortened legs on both guide plates).

Click for larger image

With the kits temporarily bolted into place, you can see the slot (arrowed) that the bolt moves along during adjustment. At the arrowed end, the slot is held in the right orientation by the legs, but at the nearer end, the slot is prevented from turning only by the clamping force of the nut. Further, the slotted washers, which sit in the enlarged holes on small shoulders, aren’t all that well located. A much stronger assembly would result if the slotted washers were welded to the strut bracket. This would: 1) strengthen the area weakened by the enlarging of the holes, (2) prevent any possibility of the slotted washer rotating, and (3) prevent these washers slopping around within the holes.

Click for larger image

So welding is exactly what we did. You can see how the slotted pieces of steel are now strongly held in place on the strut bracket. The shoulders on the back of these pieces are meant to be a push-fit in the enlarged holes – but as we said above, the fit often leaves a bit to be desired. The welding was done on both sides – the closer welds (green arrows) and also on the side furthest from the camera (red arrows). A local welder charged AUD$30 to do the job with arc welding.

Click for larger image

After being cleaned-up with a wire brush and then painted black with a spraycan, here’s what the lower strut assembly looked like. Note the slots parallel to the road along which the bolts can move during camber adjustment.

Fitting

Click for larger image

The next step in fitting is to reinstall the strut, leaving out the bottom two bolts. A bush is then inserted in each of the holes in the wheel support casting. (Why the need for the bushes? See the ‘Undersize Bolts?’ breakout box.)

Click for larger image

The eccentric washer is then selected and placed on the bolt so that the small projections face away from the head and then...

Click for larger image

...the bolt should be lightly smeared with anti-seize compound.

Click for larger image

The bolt can then be inserted and the other washer with the D-shaped cut-out installed at the other end, its small prongs facing the head of the bolt. (When the nuts are done up, these prongs bite into the guide washers, helping lock the assembly together.)

Click for larger image

The serrated washers are then placed on the bolt...

Click for larger image

...followed by the nut.

Click for larger image

Before going any further, and with the nut only finger-tight, rotate the camber adjustment bolt and make sure that you can see the hub assembly moving in and out. If it doesn’t, you may have inadvertently swapped the eccentric D-washer for the non-eccentric D-washer. (We speak from experience!) Note that a small hex-extension is provided so that the recessed hex-head bolt can be turned with a normal 12mm spanner.

Click for larger image

If you are using two complete kits, the other camber adjustment bolt assembly can now be installed. If you are using only one kit, the normal factory bolt goes back into the other hole.

Click for larger image

To get the car down to the wheel aligners, adjust the bolts so that the eccentricity of the washers shows that they are centred in their slots. This should give near-factory camber - anyway, sufficiently accurate for a short trip to an alignment machine!

Wheel Alignment

Click for larger image

Make sure that when you book-in the car you tell the alignment company that you have a camber kit installed. (Some aligners consider an alignment to be a toe setting alone!) On this car the maximum camber (with both bolts being adjusted) proved to be about 2.5 degrees negative on one side of the car and 1.7 degrees on the other. We had the camber set to 1.7 degrees each side, with a total toe-in of 4mm. The alignment cost AUD$44.

Click for larger image

The resulting camber is visually able to be seen – the front wheels are leaning in at their tops. This much camber should be used where previously outside shoulder tyre wear was noticeable – that is, the car was working hard those areas of the tyre. In this car, a Toyota Prius, the alignment change resulted in much less understeer and better steering feel, the latter especially noticeable in high speed sweepers. However, the downside is that if the car is driven gently, more tyre wear will occur on the inside of the tread.

But we don’t think that will be a problem in this case....

Contact: www.k-mac.com.au

One of the two camber kits used in this story was provided free by K-Mac.

Undersize Bolts?

Click for larger image

Many camber adjustment kits replace the factory bolt with a smaller diameter unit that incorporates an eccentric – as shown here.

Click for larger image

K-Mac makes much of the fact that they don’t use undersized bolts of above type in their camber kits. “Your customers expect you to sell safety. No undersized crank bolts” say their literature that’s directed at workshops. Trouble is, in the case of the 15mm bolts standard on this Toyota, the provided K-Mac bolts actually are undersized – they’re 13.8mm. That’s why the bushes are provided.

Click for larger image

In fact, the camber kit comes in packaging marked as suiting “14/15mm bolts” – the provided bolt is ~14mm and the bush, ~1mm. (The same appears to apply to the “16/17mm” kit.)

Click for larger image

So in this 15mm application, the bolts are undersized by about 1mm. We think is a clear case of deceptive advertising for the company to claim otherwise. That said, we would still prefer 1mm undersized bolts to the much greater undersize of some camber kits...

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
How to use hand tools for best results

DIY Tech Features - 4 August, 2007

Using Hand Tools - Spanners and Sockets

Riding a DIY electric bike

DIY Tech Features - 18 February, 2005

Building an Electric Bike Part 3

How Chrysler developed a 2.4 litre turbo

Technical Features - 5 July, 2003

Designing a Factory Turbo Engine

A press so huge it can forge titanium beams over 5 metres long

Special Features - 29 October, 2013

The Wyman Gordon 50,000 ton forging press

Fuel cells are being touted by mainstream car companies, but you have to wonder...

Technical Features - 24 October, 2007

Alternative Cars, Part 7 - Fuel Cells

The technology of Nissan's famous twin turbo V6

Technical Features - 28 February, 2008

The Nissan VG30DETT

How they did it

Special Features - 13 October, 2009

Building the Sydney Harbour Bridge

The most important aircraft ever?

Special Features - 15 December, 2009

The Wright Flyer III

The Black Box is an electronic handling revolution

Technical Features - 10 February, 2009

Adjustable Stability Control!

An extraordinary engine that was light, powerful and fuel-efficient

Special Features - 5 March, 2013

Napier Nomad

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip