Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


DIY Brake Upgrade, Part 2

Fitting slotted discs and hi-po pads

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Part 2 of a 3-part series
  • Fitting new pads
  • Fitting new discs
  • Step-by-step for front and back on a typical FWD
Email a friend     Print article
This article was first published in 2004.

Last week we inspected the brake system and found a need for new front discs and pads. The rears were fine but we decided to also do them as well. The new discs are slotted RDAs and the pads, EBC ‘blacks’ – the street level pads.  The car is a Toyota but much the same applies in any late model small car.

The Parts

Click for larger image

Here are the new RDA discs. As you can see, they’re slotted – a process that adds AUD$20 to the cost of each disc. Slots aid in (very slightly) reducing disc mass but their main benefit is in increased brake bite (the pads are swept clean each rotation) and better out-gassing (there are paths for the gases to escape that would otherwise remain trapped between the pad and the disc). Oh yes, and there’s another advantage - appearance...

Click for larger image

The new pads can be seen here. The small pads are for the rear discs and the larger pads are for the fronts. (Front brakes are always sized larger that rear brakes because when the car is decelerating, there is a forward weight transfer so the front brakes can do more braking without locking the wheels. IOTW, the front brakes work harder, so they’re bigger.) These EBC pads are a Kevlar composite material.

Click for larger image

The new fluid is Castrol Response, a premium brake fluid that’s widely available.

Fitting the Front Brakes

Fitting discs and pads is pretty straightforward on most modern cars. However, remember that you are dealing with an area very important to safety so it’s always best to have a workshop manual available – even just a basic Gregorys or Haynes style of book.

Click for larger image

The first step is to undo the bolts holding the caliper in place.

Click for larger image

The caliper can then be removed from the disc.

Click for larger image

The caliper, which is still connected to the body via the brakeline, is then lifted above the disc and hung from a piece of wire. Never suspend the caliper from just the brake hose.

Click for larger image

The discs can then be removed. This type of disc is held in place by the wheel lug nuts, so once these are undone, the disc can be pulled straight off. However, over the years discs tend to weld themselves in place. The factory is aware of this problem so they provide threaded holes in the discs through which bolts can be inserted so that...

Click for larger image

... as you tighten the bolts, the disc gets forced off.

Click for larger image

Once loosened in this way, the disc can be pulled off by hand.

Click for larger image

The new disc is a direct replacement for the old, but before putting it on the hub, make sure that the hub is clean of rust or corrosion. A wire brush is being used here.

Click for larger image

The new disc must be cleaned of its protective oils before being put into service. Wax and grease remover makes a good cleaner...

Click for larger image

...to make sure that the disc is free of any contaminant.

Click for larger image

The disc can then be placed over the hub before...

Click for larger image

...a couple of wheel nuts are used to lock the disc temporarily in place. This is a good move as it will quickly show you if you have any problems – eg if the disc fouls the caliper or (later in the process) the pads.

Click for larger image

While the front caliper is off, it’s a good idea to push the brake piston(s) back as far as possible into the cylinders. One way to do this is with a G-clamp, applying one arm of the clamp to one of the (old!) pads and the other arm to the other end of the caliper. This creates room for the much thicker new pads that you’ll be putting into place.

Click for larger image

With this caliper design, pad replacement requires bolting the caliper back into place and then removing just the 'bridge' part. So here is the caliper – complete with old pads – being bolted back over the new disc.

Click for larger image

Two bolts are undone and then...

Click for larger image

...the bridge part of the caliper can be pulled off, revealing...

Click for larger image

...the pads and their retaining springs.

Click for larger image

The old pads can be pulled out but before the new pads are put in, the anti-squeal shims should be swapped over after being lightly lubricated with disc brake grease or anti-seize copper grease.

Click for larger image

Put the new pads in place and add their clipped-in springs and it’s time for the....

Click for larger image

...caliper bridge to be placed back over the assembly.

Click for larger image

With the retaining bolts done up and all bolts checked for tightness, the front disc-and-pads upgrade is done.

Click for larger image

So that the hubs don’t go all rusty and ruin the appearance through your alloy wheels, spray some paint over the inner part of the discs. You needn’t worry about masking-off the face of the discs – once being driven, the overspray will soon be removed by the friction of the pads.

Click for larger image

Finished!

Direction of Slots?

Slotted discs are directional – that is, they have a left-side fitment and a right-side fitment. Brembo state their slotted discs “should be installed such that the end of the slot nearest the outer edge of the disc contacts the pad first”.

Rear Brakes

Click for larger image

Doing the rear brakes involves much the same process... but with some significant differences. This caliper design allows the brake pads to be removed before the caliper is unbolted. So after removing the pad spring clips...

Click for larger image

..and placing them in a marked container (you wouldn’t believe how easy it is to lose these little beasties)...

Click for larger image

...the pad retaining pins can be pulled out...

Click for larger image

...and then the pads removed.

Click for larger image

The caliper retaining bolts can then be undone before...

Click for larger image

..the caliper is removed and hung from a piece of wire.

Click for larger image

The disc may then just pull off (or need the persuasion of a rubber mallet or the screw-in bolts trick shown with the front brakes). Here it just pulled off.

Click for larger image

Again the hub should be thoroughly cleaned with a wire brush before...

Click for larger image

...the new disc is also cleaned with a solvent.

Click for larger image

The new disc can then be placed over the hub.

Click for larger image

The caliper can be bolted back into place over the new disc and the...

Click for larger image

...lubricated anti-squeal plates swapped over to the new pads. Note that in this case the new and old pads were of much the same thickness so the piston didn’t need to be forced back into its cylinder.

Click for larger image

The pins and clips were then placed back into the caliper.

Click for larger image

Finished!

Next week – changing the fluid, bleeding the brakes and then bedding them in.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
Sand moulds to cast aluminium

Technical Features - 25 November, 2008

Metal Casting, Part 2

The effects of changing dwell time

Technical Features - 26 August, 2014

Ignition coil dwell time

A real and effective $75 handling upgrade

DIY Tech Features - 8 December, 2004

Rear Sway Bars: Improving FWD Handling

How tyres really work on the road

Technical Features - 9 August, 2007

Tyres, Grip and All That

A day of testing with the Hyundai i30 diesel rally car

Special Features - 18 May, 2010

Pushing Limits

Almost beyond belief in its brilliance

Special Features - 12 May, 2009

The Amazing Tesla

Introducing a breakthrough in DIY electronics

DIY Tech Features - 6 October, 2009

eLabtronics EZ System, Part 1

A 2-amp variable voltage power supply for under $10!

DIY Tech Features - 1 October, 2013

Cheap Power!

Squirt your intercooler spray for 5, 10 or 20 seconds - all at the press of a single button!

DIY Tech Features - 2 September, 2008

Intercooler Spray Squirter

Books that you'll keep forever

Special Features - 24 March, 2009

The Ten Must-Have Books

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip