Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Turbo'd for Fuel Economy

The way of the near future

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Higher thermal efficiency
  • Better bottom-end power
  • Example engines
Email a friend     Print article

After decades of petrol engine turbochargers being associated with performance, turbocharged engines are now being developed that use forced aspiration to improve fuel economy. Yes, you can still have performance – but with carbon-aware fuel economy numbers that were once the stuff of pipe-dreams.

Turbocharging

Click for larger image

Turbochargers are deceptively simple devices. A turbine wheel, capable of withstanding very high temperatures, is placed in the exhaust flow. The flow and heat of the exhaust gases – energy normally wasted – spins the turbine at very high speeds. Connected at the other end of the spinning shaft is a compressor that forces air into the engine. The faster the turbine spins, the faster the compressor spins. Thus the higher the engine power (and so exhaust flow), the more power that in turn can be produced by adding fuel to the extra air being crammed in.

A turbocharged engine can breathe a greater mass of air than its swept volume would normally allow. So - if you like - a 2 litre engine can become a 4 litre engine – yet increase in size and weight by only a modest amount. It’s this ‘something for nothing’ outcome that has so driven turbocharged performance.

Click for larger image

In most turbocharged production cars, the turbo engine will produce 30 – 50 per cent more power than its naturally aspirated brother. But in aftermarket and racing performance applications, this increase can be 100, 200 or 300 per cent!

But what about turbos in economy applications?

Turbocharged Economy

A turbo engine has the potential to be more economical than a naturally aspirated engine for two reasons.

  • Thermal Efficiency

A turbocharged engine is more thermally efficient than a naturally aspirated engine. This is easy to understand when you remember that the turbo uses energy normally wasted out of the exhaust.

If you stand behind a car on a dyno as it undergoes a full power run, you’ll be amazed at the force of the gas coming out of the tail-pipe – you can feel it from literally metres behind the car. As it exits the engine, the gas is also hot – up to 800 degrees C – and it is hot because it has energy that can do work.

Since a turbo makes use of both the heat and flow, in a turbo car a greater amount of fuel is converted to useful work.

Click for larger image

(Another way of looking at this is to consider that there is always a temperature drop across a turbo. That is, the temperature of the exhaust gas measured in front of the turbo is always higher than the temperature of the exhaust gas measured after the turbo. This temp change is indicative of the energy being taken from the exhaust gas. The turbo also takes much of the pulsing out of the exhaust gas – the reason why a turbo car usually needs less muffling of its exhaust. Again, the turbo is drawing energy from the exhaust.)

So a turbocharged engine is more thermally efficient than a naturally aspirated engine.

  • Shape of Power Curve

The other reason that a turbo engine has the ability to more economical relates to the way in which it develops power.

In a given naturally aspirated engine, the power developed at each rpm depends on aspects such as valve timing and intake and exhaust manifold tuning. For example, the engine might be ‘tuned’ to develop a lot of power at low revs. However, even with variable valve timing and variable inlet manifolds, a naturally aspirated engine with good bottom-end power is very unlikely to have good top-end power – the compromise to get the good bottom-end power output is simply too great.

The reason that good bottom-end power will improve fuel economy is that the car will be able to use low engine revs more of the time. That is, the gearbox will not need to change down, so keeping revs lower. This is important for economy as the frictional losses inside the engine increase rapidly with higher revs – the throttled engine becomes less efficient as revs rise. But low engine revs can only be used if the engine has sufficient power to propel the car at those revs!

Of course, fitting a bigger engine will give good power at low revs – but a bigger engine will also have higher internal friction, so there’s no overall gain.

Therefore, to gain the best real world economy, what is needed is a small engine (so having low internal friction) running at low revs (again, small internal frictional losses) that develops lots of power at those low revs.

And the best way to efficiently give a small engine good low-down power is to turbo it.

Comparisons...

So that’s what the theory suggests – but what about the real world? Two engines that make for a great comparison are the 2-litre designs produced by Volkswagen. (Here Skoda data is used but the engines are the same across a range of Volkswagen/Audi/Skoda cars.)

The two engines are the 2.0 FSI and the 2.0 FSI Turbo.

Volume

(cc)

Bore and Stroke

(mm)

Compression Ratio

Power

(kW at rpm)

Torque

(Nm at rpm)

2.0 FSI

1984

82.5 x 92.8

11.5:1

110 @ 6000

200Nm @ 3500

2.0 FSI Turbo

1984

82.5 x 92.8

10.5:1

147 @ 5100-6000

280Nm at 1800-5000

From this table it can be seen that the engines are the same swept volume and use the same bore and stroke. They also both have high pressure direct fuel injection (“FSI”), the same number of cylinders and so on. The naturally aspirated engine uses a compression one ratio higher than the turbo engine and the turbo engine develops 34 per cent more peak power than the naturally aspirated design.

So far – apart from the very high compression ratio of the turbo engine – all is as it has been for more than two decades of turbocharging.

However, look at the torque output of the turbo engine! It develops 40 per cent more torque 1700 rpm lower in the rev band!

Now people often get confused when talk turns to torque, so let’s forget torque and look at what really matters – power. Skoda has been kind enough to release full power and torque graphs for these two engines.

Click for larger image

This is for the naturally aspirated engine...

Click for larger image

...and this is for the turbocharged engine.

Let’s take a look at the power being developed by each engine at low revs.

2.0 FSI

2.0 FSI Turbo

Difference

1500 rpm

27kW

40kW

48%

2000 rpm

38kW

58kW

53%

2500 rpm

57kW

74kW

30%

To put it simply, the turbo engine has around 50 per cent more power at the bottom end of the rev range! And it does this without giving away anything at the top end – in fact, as already mentioned, the turbo engine has 34 per cent more peak power than the naturally aspirated engine...

Therefore, when driving the turbo’d car, the engine requires far fewer gear down-changes (either manually or via an auto gearbox) and so stays at lower engine revs more often. Despite having a lot more power at the top end, for economy it is the power available at the bottom-end of the rev range that really matters – and the Turbo 2.0 FSI has it in spades.

Unfortunately for this comparison, the two engines aren’t available in Skodas with the same transmissions – the 2.0 FSI has a six-speed auto and the turbo 2.0 FSI a six-speed manual. However, modern auto transmission cars seldom use much more fuel than manual trans cars – indeed, there are some autos that give better fuel economy than manual trans cars.

In the Australian government test cycle, the naturally aspirated Skoda 2.0 FSI has a fuel consumption of 8.5 litres/100km while the turbo 2.0 FSI has a tested economy of 8.1 litres/100km! That’s right, the car with more power is also more economical! The CO2 emissions are also as you’d by now expect – 203 grams/kilometre for the naturally aspirated engine and 193 for the turbo.

Oh yes, and the turbo 2-litre Skoda gets to 100 km/h in 7.3 seconds versus the naturally aspirated car’s 10.1 seconds!

Implications

So let’s take a step back. In the comparison shown above of the two 2-litre engines, the turbo engine has better fuel economy, better CO2 emissions, 50 per cent more bottom-end power and 34 per cent more top-end power.

In short, it’s better in every respect (except, it must be said, cost to build).

Having driven both engines on the road in recent times, the turbo engine is massively better – and in fact in freeway travel, we scored an even greater fuel economy win to the turbo engine than the above official test figures show.

But if we’re chasing fuel economy rather than performance, wouldn’t it make more sense to use a smaller engine and then turbocharge it to match the performance (but not the thirst) of the larger naturally aspirated engine?

With another engine, the 1.8 litre turbo TSI, that’s exactly what Volkswagen/Skoda have done.

Volume

(cc)

Bore and Stroke

(mm)

Compression Ratio

Power

(kW at rpm)

Torque

(Nm at rpm)

2.0 FSI

1984

82.5 x 92.8

11.5:1

110 @ 6000

200Nm @ 3500

2.0 FSI Turbo

1984

82.5 x 92.8

10.5:1

147 @ 5100-6000

280Nm at 1800-5000

1.8 TSI Turbo

1798

82.5 x 84.2

9.6:1

118kW@5000-6200

250Nm at 1500-4200

Click for larger image

The smaller turbo engine again has strong bottom-end power, though not to the same extent as the 2.0 litre turbo. But its bottom-end is still much better than the naturally aspirated engine:

2.0 FSI

1.8 TSI Turbo

Difference

1500 rpm

27kW

38kW

41%

2000 rpm

38kW

52kW

37%

2500 rpm

57kW

79kW

39%

So even though it’s a smaller engine, the turbo’d 1.8 easily outperforms the naturally aspirated 2 litre at the critical-for-economy bottom end of the rev range. And of course, it does even better on fuel economy – 7.7 litres/100km and CO2 emissions of 184 grams/kilometre.

In fact, in terms of power production, you can see that the engine could probably be smaller still – say, a 1.5 litre turbo.

Conclusion

Modern engines using well matched turbos and other technologies like direct fuel injection are capable of exceeding the performance of larger naturally aspirated engines across the full rev range – from just off idle all the way to the redline. Their immense bottom-end power and intrinsically higher thermal efficiency also allows them to develop much better real-world fuel economy. As turbocharging is a technology already well developed and understood, expect to see a lot more turbocharged, downsized petrol engines performing for all the world like big engines – but without the thirst and emissions production.

Commercial Developments

As this article was being prepared, huge automotive parts manufacturer Bosch released information that it is about to form a joint venture with Mahle to manufacture turbos. Says the press release:

As part of the downsizing concept for the engines of the future, exhaust gas turbochargers are one of the key technologies for achieving a sustained cut in fuel consumption and CO2 emissions. The use of exhaust gas turbochargers is already common in modern diesel engines, and they are expected to become more prevalent in gasoline engines as well. This also calls for more widespread use of advanced injection technologies. This is an area in which Bosch already occupies a globally leading position, both with gasoline direct injection and with common-rail technology for diesel engines. MAHLE has many years of experience in the development and manufacture of high temperature-resistant turbocharger components. In addition, its subsidiary MAHLE Powertrain specializes in the development, design, and application of turbocharged engines.

"This joint venture will now allow us to offer our customers from a single source a complete product portfolio for reducing fuel consumption and emissions," said Dr.-Ing. Bernd Bohr, chairman of the Bosch Automotive Group.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
Some of the best wind tunnel pics you'll ever see

Technical Features - 4 July, 2007

Aero Testing, Part 4

Why turbo engines give better fuel economy

Technical Features - 13 February, 2008

Turbo'd For Fuel Economy

Assessing the performance of an amazing human powered vehicle

DIY Tech Features - 15 January, 2008

Air 150 Recumbent Trike, Part 2

How Chrysler developed a 2.4 litre turbo

Technical Features - 5 July, 2003

Designing a Factory Turbo Engine

Electricals

DIY Tech Features - 3 April, 2012

A New Home Workshop, Part 7

Steps in mixing and matching front brake components

DIY Tech Features - 29 May, 2012

Selecting components for upsized front brakes

Building a programmable temperature alarm

DIY Tech Features - 13 October, 2009

eLabtronics EZ System, Part 2

Building a heavy duty mount

DIY Tech Features - 24 July, 2012

Relocating the alternator

A press so huge it can forge titanium beams over 5 metres long

Special Features - 29 October, 2013

The Wyman Gordon 50,000 ton forging press

Build your own battery charger for nearly nothing

DIY Tech Features - 21 October, 2008

Dirt Cheap DIY Battery Charger

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip