Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Electric Express

Unleashing 2000 amps

by Julian Edgar

Click on pics to view larger images


Click for larger image

There might be a few people left in the world who think electric vehicles are passé. You know, suitable only for commuting by those travelling just a few kilometres. And as for performance – well, forget it. Trouble is, no-one told Colorado’s Bill Dube and his team...

Bill owns the world’s quickest electric drag bike – and with a time of 8.168 seconds at 155.78 mph for the quarter mile, in anyone’s terms it’s not slow.

Bill has been drag racing electric vehicles since 1997, starting with his electric daily driver, a 1985 VW cabriolet. But when he kept breaking things he decided to build a dedicated electric drag racer – and the aptly named Killacycle is it. The bike first raced in 1999 and has since been constantly developed and uprated.

“The bike is very simple,” says Bill with classic understatement. “It is, as I love to say, just a giant cordless drill with wheels.”

Click for larger image

The motorcycle is powered by no less than 990 small lithium ion cells provided by A123 Systems. The cells weigh just 73kg and yet can supply up to 1575 amps at 374V. Another way of putting that is to say that 390hp is available... Including burn-outs, the KillaCycle could make seven runs on just one battery charge. Another interesting point: a drag run uses just 10 cents of electricity!

Custom battery management controls, developed by Denver CNC, are used. The electric motors, two 6.7 inch Model L-91 motors that drive a chain drive to the rear wheel, are controlled by a Café Electric Z2K Motor Controller. The motors are series-wound DC. As you’d expect, no off the shelf motors are suitable so Bill has the L-91 motors modified to suit.

“Jim Husted of Hi-Torque Electric beefs these up for me and fixes them when we turn them into blobs of molten metal with plasma burns all over them,” says Bill.

“We launch the bike with both motors in series. We cram 2000 amps through them to get about 400 ft-lbs of torque out of each one. This translates into almost 2000 ft-lbs of torque at the 10 inch wide rear tyre.

“The bike takes off from the line pulling about 2.9 g's, covering the first 60 ft in 1.169 seconds. This means that the bike is doing 60 mph at about the 47 ft mark (and 1.04 seconds.)

Click for larger image

“While in series, the motors each get all the controller output current of 2000 amps, but they only get a maximum of half the pack voltage of 375 volts. As the motors spin up, they need more voltage, so we switch them into parallel.

“We switch the motors into parallel about a third of the way down the track. When you are riding the bike, this feels like you are shifting an automatic transmission. In parallel, we divide the available 2000 amps into each motor, but each can get the full pack voltage. This halves the maximum torque but lets the motors spin at about twice the speed.

“It is very much like shifting gears, but in an electrical sense.

Click for larger image

“We heat the 990 A123Systems M1 cells (26650) up to 75 degrees C in the pits using heaters built into the pack. Ordinary Li-Ion laptop cells would have flames coming out of them at this temperature, by the way.

“We do this heating to get maximum horsepower from the cells. We pull 175 amps out of each of the 70 gram cells. When the bike comes back from the run, the battery pack temperature is near (or just a touch over) 100 degrees Celsius. We then cool the pack down to 75 C by attaching a shop vacuum to it and blowing air through it.

“It takes about 10 minutes for us to recharge the pack and be ready for another run.”

Scotty Pollacheck rides the bike and also is responsible for tyres and suspension set-up.

“Scotty can run the bike using the throttle or simply push the launch button and let the controller run its program,” continues Bill.

“The throttle is a lot like the volume control on your stereo. It has a 5 k-ohm variable resistor built into it that sends a signal to the controller as you twist the grip.”

And if something goes wrong, how does Scotty find the ‘off’ switch?

Click for larger image

“There are two $900 "Bubba" EV500 KiloVAC contactors, one on the positive of the pack output and the other on the negative. These are used for safety disconnects should the controller get stuck ‘on’ and directly connect the battery to the motors. A flick of a switch with Scotty's left thumb, or a yank on the lanyard attached to his right arm, will open each of these contactors and will shut the bike down instantly.”

Apart from its drive system, mechanically the drag bike is conventional. The front end was made specifically for drag racing by Trac Dynamics. The wheels are made by PMFR. The frame was scratch built from 4130 aircraft tubing by Wes Messick while the body was made by AeroTech.

Click for larger image

And are Bill and his team content to rest on their laurels? Nope!

“We are trying to find a motor-control AC inverter company to partner up with that can help us build the 1000 horsepower drive package we will need when we go to the next level with A123 Systems Ultra-cells.

“As spectacular as our present A123Systems nanophosphate M1 cells are, these new Ultra cells will have nearly twice the horsepower that we are getting now in the same weight battery pack. If we can build the inverter and motors we need, we have a very good chance at taking away some records from the top fuel drag bikes.

“The power-to-weight numbers are there, we just need help building this 1000 horsepower monster inverter...”

More power to them!

To see the bike in action, go to www.youtube.com

Sponsors:

A123Systems (Batteries)

A123Racing

Denver CNC

Hi-Torque Electric

Quality Tire

AirTech Streamlining

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
Getting a great looking and durable finish

DIY Tech Features - 21 October, 2014

Powdercoating of fabricated parts

A 2-amp variable voltage power supply for under $10!

DIY Tech Features - 1 October, 2013

Cheap Power!

The most amazing flying machines you've ever seen

Smart Technology - 5 March, 2002

Between the Wind and the Waves: Ekranoplans

The effects of changing dwell time

Technical Features - 26 August, 2014

Ignition coil dwell time

Describing how diesel burns

Technical Features - 16 April, 2013

Diesel cetane ratings

Reducing fuel use through electronic tweaks

DIY Tech Features - 27 September, 2006

Electronic Ways to Improve Your Fuel Economy

The series conclusion

DIY Tech Features - 15 May, 2012

A New Home Workshop, Part 10

How to make your own airbox - and test its effectiveness

Technical Features - 19 April, 2008

Building and Testing an Airbox

The revs and loads at which engines use least fuel

Technical Features - 10 April, 2008

Brake Specific Fuel Consumption

Drains and landscaping - and passing council inspection!

DIY Tech Features - 9 September, 2008

Building a Home Workshop, Part 5

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip